Veritas Scraping Tools

Veritas HCS Blade Assembly  (Ref: 476832)

The high-carbon-steel (HCS) blade is great for finishing bare wood surfaces. The 75 x 75 x 1.6mm HCS blade comes with one edge bevelled.

£9.30

£11.16

Veritas Replacement Blade 75 x 75mm for Ball-Joint Scraper  (Ref: 200809)

Veritas Variable Burnisher  (Ref: 510438)

Makes raising a burr an easy job
Carbide rods fixed at an angle in brass hub
Face dial allows angle to be set between 0° and 15°
Plastic construction will not damage scraper's face
Includes cabinet scraper and full instructions

Although filing and honing a cabinet scraper is relatively easy it is the raising of a burr where problems seem to occur. The Veritas Variable Burnisher completely eliminates this problem and makes this an easy job. The burnisher has carbide rods fixed at an angle in a brass hub. The dial on the face allows the angle to be set anywhere between 0° and 15°. You rotate the knurled brass knob to your chosen angle and then lock it into place with the brass thumbscrew. The body of the burnisher is slotted so the angle is constantly maintained during use and, being made of plastic, it will not damage or scratch the scraper's face. Woodworkers used to using a traditional burnishing tool will also find this useful since it can be used to put different cutting characteristics on different edges of a scraper. This Veritas tool makes it possible for anyone to burnish a cabinet scraper to the desired angle perfectly every time. Each set includes a cabinet scraper (150 x 60mm) and full instructions.

£24.50

£29.40

Veritas Cabinet Scraper Holder  (Ref: 510436)

Accepts 140mm to 150mm long scraper blades
Glass reinforced nylon body
Clamps either side allow for projection adjustment
Central knurled knob controls amount of bow
Includes a Veritas milled edge scraper

Absorbing the heat and stress normally levied on the hands when cabinet scraping, this scraper holder made in glass reinforced nylon with brass fittings will take traditional cabinet scrapers 140 to 150mm long. The blade can be given an appropriate bow using the central screw adjuster. Work traditionally without the pain! Includes a Veritas milled edge scraper.

£26.60

£31.92

Veritas Super-Hard Curved Cabinet Scrapers - Set of 3 x 0.4mm ( 0.015")  (Ref: 510434)

Hardened to HRC 48-52
Edges milled to sharp 90°
Suitable for immediate fine work

These Veritas scrapers are hardened to HRC 48-52 for increased durability, somewhat harder than most standard scrapers. In addition, their edges are carefully milled to a sharp 90° and are suitable for immediate fine work whilst heavier work only requires a slight hook to be burnished onto their edges. Available in two sets of three curved scrapers, either 0.4mm (0.015") or 0.6mm (0.024") thick.

£9.80

£11.76

Veritas Super-Hard Curved Cabinet Scrapers - Set of 3 x 0.6mm (0.024")  (Ref: 510433)

0.6mm(0.024") thick.

£9.80

£11.76

Veritas Tri-Burnisher  (Ref: 475477)

Designed to perform all the functions of round, triangular and oval burnishers
Mirror finish to guarantee smooth hooks on cabinet scrapers
Unique shape lets you apply just the right amount of pressure
Superior surface finish avoids galling and hook tearing
Hardened to HRC58-60, this is much harder than scrapers it is used on
11" long including the hardwood handle for easy gauging and angles

This is designed to perform all the functions of round, triangular and oval burnishers. It has a mirror finish to guarantee smooth hooks on cabinet scrapers. The blade is hardened to HRC58-60 to be much harder than scrapers it is used on. The overall length is 275mm including the hardwood handle.

£27.00

£32.40

Veritas Super Hard Milled Scrapers (4)  (Ref: 476257)

Hardened to HRC 48-52 to hold an edge longer
Edges are carefully milled to a square, sharp 90°
Prepared edges save time and effort of filing and stoning
Comes in set of four
50 x 150 x 0.4 & 0.6mm for fine work
60 x 150 x 0.8 & 1mm for heavier stock
1mm scraper suitable for paint removal

Whereas most cabinet scrapers are sheared from spring steel and hardened to HRC 38-42, these Veritas scrapers are harder (HRC 48-52) and hold an edge longer. Their edges are carefully milled to a square, sharp 90°. The set includes four thicknesses: for fine work, 0.4mm(0.016") and 0.6mm(0.024") thick, each 50mm x 150mm(2" x 6"); for heavier work, 0.8mm(0.032") and 1mm(0.042") thick, each 60mm x 150mm(2.3/8" x 6").

£12.60

£15.12

Veritas Cabinet Scraper  (Ref: 474843)

Smoothes glue lines or surfaces without tear-out, digs or gouges
Allows pressure to be applied directly in line with the cutting edge
70mm wide blade, with both cutting edges ground at 45°
Shaped to protect the upward-facing cutting edge
Sole is surface ground for accuracy (80 x 85mm)
Made from ductile cast iron
Overall length 290mm. Weighs about 740g

The Veritas Cabinet Scraper can be used to smooth glue lines or surfaces such as panels and table tops, or where there is tricky grain, without tear out, digs or gouges. The sole is longer and the handles have been placed further back and slightly lower than the No.80 on which it is based. This allows pressure to be applied directly in line with the cutting edge and prevents the blade from catching when the scraper runs off the end of the workpiece. The 70mm(2.3/4") wide blade has both cutting edges ground at 45° to permit preparation of two edges at once. The 80mm (3.3/16") x 85mm(3.3/8") sole is surface ground for accuracy. The body is made from ductile cast iron, overall length 290mm(11.1/2") weight approximately 740g(1lb.10oz).

£52.00

£62.40

Veritas Scraper Shave  (Ref: 701976)

The Veritas Scraper Shave is a versatile small scraper suitable for small-scale work, fine detailing, or any application where a normal scraping plane would be too large. The design of the tool allows a controlled scraping action that effectively smoothes the workpiece. Can be used as a companion tool with Veritas Chair Devils for smoothing of non-round chair parts such as crest rails, arm bows and seat blank edges. Similar in construction to the Chair Devils, it has a machined steel body, comfortable Bubinga handles, and a solid brass machined toe and thumbscrews. The high-carbon steel blade is 1mm(0.040") thick and hardened to HRC 48-52, with a 45° cutting edge that can be readily burnished to create a long-lasting hook.

£44.00

£52.80

Veritas Chairmaker's Scraper  (Ref: 701968)

While this Chairmaker's Scraper was designed primarily for chairmakers' use, it can be used for any other scraping task in the workshop.

The appeal of this tool is that it can be used as is for scraping flat surfaces with the included straight blade. For scraping round pieces, additional blades are available: three concave shapes in 12.7mm(1/2"), 22mm(7/8") and 31mm(1.1/4") diameters and one convex 38mm(1.1/2" radius).

The straight blade could also be ground to a specific shape. All blades are made from 1.5mm(0.060") thick high-carbon steel. The machined cast steel body is fitted with a large rear handle and a front knob of African rosewood

£43.00

£51.60

Veritas Straight Blade for Chairmakers Scraper  (Ref: 701969)

Veritas Concave Blade for Chairmakers Scraper - 12.7mm (1/2")  (Ref: 701970)

Veritas Concave Blade for Chairmakers Scraper - 22mm (7/8")  (Ref: 701971)

Veritas Concave Blade for Chairmakers Scraper - 32mm (1.1/4")  (Ref: 701972)

Veritas Convex Blade for Chairmakers Scraper - 38mm (1.1/2")  (Ref: 701973)

Veritas Scraping Plane  (Ref: 701915)

The ideal tool for final smoothing
Tear-out virtually eliminated with cutting action of included scraping blade
Bubinga front knob and rear handle
Integral thumbscrew to bow blade to eliminate ridges

The Veritas scraping plane is the ideal tool for final smoothing. Tear-out is virtually eliminated with the cutting action of the included scraping blade. The generous Bubinga front knob and rear handle make it comfortable to use for extended periods and the large sole ensures an accurately flattened surface. The adjustable frog enables blade angles from 0° to 25°, providing fine control of the cutting action. A feature unique to the scraping plane is an integral thumbscrew that bows the blade to eliminate ridges in the work surface caused by blade corners. The plane comes with a 1.4mm (0.055") high-carbon steel blade suited to this technique, and an optional 3.2mm (1/8") thick blade of A2 tool steel is available for those who prefer uncambered blades. Also available is a 3.2mm(1/8") thick A2 tool steel toothed blade at 25 teeth per inch. All blade styles are 73mm(2.7/8") wide, hardened to HRC 48-51, and come with the cutting edges ground at 45°. The 240mm (9.1/2") ductile cast iron body has been fully stress relieved, machined, and surface ground on the sole. Weight is 1.8kg(4lb).

£150.00

£180.00

Veritas HCS Blade for Scraping Plane  (Ref: 701916)

Veritas A2 Blade for Scraping Plane  (Ref: 701917)

Veritas A2 Toothed Blade for Scraping Plane  (Ref: 701918)

Veritas Small Scraping Plane  (Ref: 210948)

Designed for one-handed use
Articulating palm rest for comfortable, controlled grip
50mm x 1mm thick high-carbon-steel blade
Allows clean, accurate cuts flush against a perpendicular surface
Blade is ground at 45°, allowing you to burnish a hook with ease
The 135mm long ductile cast iron body, weight 700g

The Veritas Small Scraping Plane is a great tool for the final smoothing of small, flat surfaces, even highly figured timber, or small areas of difficult grain within a larger surface. The scraping plane comes into action after the surface has been prepared as well as possible using a finely tuned smoothing plane. What the scraping plane does is to replace the need for sanding prior to applying a finish. Because the scraping plane cuts the wood fibres rather than tears them, it will further bring out the beauty of the wood grain, rather than mute it as sandpaper would. This plane is supplied with a 50mm by 1mm thick high carbon steel blade with its cutting edge ground at 45°. The pitch, or blade angle, is 20° forward from vertical.

The full width blade and adjustable palm rest (which pivots to either side) allows the plane to be used right up to a vertical face. Depth of cut is regulated by applying camber to the blade. By slightly bowing or arching the blade, you also eliminate ridges in the work surface caused by blade corners.

£86.00

£103.20