Veritas Saws

Veritas Gents Saw - Rip Cut  (Ref: 952907)

0.4mm thick high-carbon steel
Injection moulded back creates a solid one-piece blade/spine/mount assembly
Brass nut secures comfortable Bubinga handle
Saw cuts easily and stays true

Sharing the same, advanced materials as the Veritas dovetail and carcass saws, these Gent’s saws have 200mm long high-carbon steel blades just 0.4mm thick with 0.08mm of teeth set per side. The 20tpi ripsaw has teeth with a 14" rake angle and a 60° included angle. The teeth on the 22tpi crosscut saw have a rake angle of 15°, an included angle of 60° and alternating 15° bevel angles so that they sever rather than tear wood fibres. Both saws have a cut depth of 41mm. For strength and rigidity, the glass and stainless steel-filled polymer spine is moulded over the blade and handle stud. A brass nut secures the Bubinga handle to the blade. Made in Canada.

£38.30

£45.96

Veritas Gents Saw - Cross Cut  (Ref: 952908)

Veritas Rip Cut Carcass Saw  (Ref: 950979)

The saw has a 275mm (11") long by 0.5mm thick high-carbon steel blade filed for rip cutting at 12tpi. The teeth have a rake angle of 10°, an included angle of 60° for fast and accurate cutting along the line of the grain. The depth of cut is 60mm. The back of this saw is injection moulded under high pressure onto the blade and stainless-steel handle-mounting bolt. This forms a solid one-piece blade/spine/mount assembly. The material used for the back incorporates stainless-steel powder for weight, glass fibre for stiffness, and a polymer resin binder. A brass nut fastener secures the comfortably shaped Bubinga handle. The saw has great balance it cuts easily, stays true and the grip makes for a comfortable and secure grip. Overall length 415mm (16.1/4")

£45.00

£54.00

Veritas Crosscut Carcass Saw  (Ref: 950978)

The saw has a 275mm (11") long by 0.5mm thick high-carbon steel blade filed crosscut at 14tpi. The teeth have a rake angle of 15°, an included angle of 60° with alternate 15° bevels to efficienlty sever wood fibres rather than tear. The depth of cut is 60mm. The back of this saw is injection moulded under high pressure onto the blade and stainless-steel handle-mounting bolt. This forms a solid one-piece blade/spine/mount assembly. The material used for the back incorporates stainless-steel powder for weight, glass fibre for stiffness, and a polymer resin binder. A brass nut fastener secures the comfortably shaped Bubinga handle. The saw has great balance it cuts easily, stays true and the grip makes for a comfortable and secure grip. Overall length 415mm (16.1/4").

£45.00

£54.00

Veritas Fine-Tooth Dovetail Saw  (Ref: 211804)

For woodworkers who prefer a fine-tooth dovetail saw, Veritas produce a premium example with a 20 teeth per 25mm (20tpi blade) filed for rip cutting. It has a 235mm (9.1/4") long by 0.5mm thick high-carbon steel blade. The teeth have a rake angle of 14°, and an included angle of 60°. The depth of cut is about 40mm (1.9/16").The back of this saw is injection moulded under high pressure onto the blade and stainless-steel handle-mounting bolt. This forms a solid one-piece blade/spine/mount assembly. The material used for the back incorporates stainless-steel powder for weight, glass fibre for stiffness, and a polymer resin binder. A brass nut fastener secures the comfortably shaped Bubinga handle. The saw has great balance it cuts easily, stays true and the pistol grip helps make the saw feel like an extension of your arm. Overall length 360mm (14.1/4")

£44.00

£52.80

Veritas Small Crosscut Saw  (Ref: 211803)

The saw has a 235mm (9.1/4") long by 0.5mm thick high-carbon steel blade filed with 16 teeth per 25mm (16tpi). The teeth have 15° rake and bevel angles. The depth of cut is about 40mm. The back of this saw is injection moulded under high pressure onto the blade and stainless-steel handle-mounting bolt. This forms a solid one-piece blade/spine/mount assembly. The material used for the back incorporates stainless-steel powder for weight, glass fibre for stiffness, and a polymer resin binder. A brass nut fastener secures the comfortably shaped Bubinga handle. The saw has great balance it cuts easily, stays true and the pistol grip helps make the saw feel like an extension of your arm. Overall length 360mm (14.1/4")

£44.00

£52.80

Veritas Dovetail Saw 230mm x 14tpi  (Ref: 210923)

The saw's spine is permanently moulded onto the back of the blade. It imparts just the right amount of weight to the blade to carry the saw effortlessly into the cut. The polished hardwood handle is shaped to fit the hand comfortably and not just to look pretty, which it also does. In fact the handle is very reminiscent of the rear tote on a bench plane and this theme is carried on in the steel rod and brass nut used to attach the handle onto the spine. A mortice and tenon joint between handle and back ensures a good solid and secure fixing between the two parts. The blade is Japanese high carbon steel, 230mm (9") long by 40mm (1.1/2") deep, with razor sharp 14tpi teeth filed with a 14° rake angle, the overall weight is 360g (12.7oz).

£44.00

£52.80

Veritas Flush-Cutting Saw - Single Edge  (Ref: 476058)

Traditionally used for the rapid trimming of plugs and dowels flush with a surface, these flush cutting saws can be used where you want to cut off a projection without damaging the surrounding or adjoining face. This is possible because the teeth are set one way only. The 22tpi Japanese tooth pattern blade cuts aggressively (on the pull stroke), but does not mark the surface that it is cutting next to. The thin blade is flexible and can be pressed flush to any surface, yet is rigid enough for good control. The saw is available with teeth cut on only one edge or in a double edged style that cuts from either side. Each is about 290mm long with 120mm of blade. These work like a charm.

£15.00

£18.00

Veritas Flush-Cutting Saw - Double Edge  (Ref: 475855)

A double edged style that cuts from either side. Each is about 290mm long with 120mm of blade.

£19.00

£22.80

Veritas Jointer & Edger  (Ref: 600304)

Dual purpose
Topping off teeth prior to re-sharpening
Provides an accurate guide for filing edges of cabinet scrapers
45° guide face for sharpening scraper and plane blades

Serving the dual purposes of topping off the teeth of a hand saw prior to re-sharpening, and providing an accurate guide for filing the edges of cabinet scrapers. A file with a maximum thickness of 4.7mm, typically a 150mm second cut hand file, is clamped into the guide and run across the saw teeth or the scraper to produce an even and square result. The 45° guide face enables other scraper blades to be sharpened. Another use for this versatile tool is for keeping your ski edges nice and sharp; how versatile can you get?

£13.00

£15.60

Veritas Right-Angle Saw Guide  (Ref: 202387)

Manufactured using precision machined aluminium extrusion with brass fittings. The reference surface is embedded with a 19mm rare earth magnet and covered with a low friction UHMW pad. The magnets keep the saw aligned; the pads allow the saw to slide easily against the reference surface. The clamp can accommodate material from 6mm to 25mm thick. The guide can be used with virtually any backless saw, however the Veritas dovetail saw is specifically designed for the job; with a 50 x 215mm, 22tpi blade, effective in both cross and rip cuts.

£33.00

£39.60

Veritas Dovetail Guide With Saw 14°  (Ref: 718157)

The Veritas dovetail guide clamps in position and holds the saw at the correct place and angle for a perfect cut. Rare-earth magnets are embedded in the anodized aluminum guide and are covered with a layer of Low-friction UHMW plastic to keep the saw perfectly aligned as you cut. You still have to chop out waste from the tails and pins, but the detailed instructions give you tips on how to do this quickly and accurately. The Clamping capacity of the guide covers material from 6 to 25mm(1/4" to 1") thick. The guide can be used with any backless saw that has approximately 0.005" of tooth set, but works best with the Veritas dovetail saw that has been designed specifically for it. The 50 x 215mm(2" x 8.1/2") blade has 22 tpi and 0.127mm of tooth set. The dozuki tooth form is effective in both crosscuts and rip cuts.

£45.00

£54.00

14° Veritas Dovetail Saw Guide  (Ref: 210528)

Veritas Dovetail Saw Only  (Ref: 202379)

1:8 Veritas Dovetail Saw Guide  (Ref: 202378)